ES 6″ Bronze – E-Series Lead-Free Bronze Alloy

The E-Series® Ultrasonic meter uses solid-state technology in a compact, tamper protected, weatherproof, and UV-resistant housing, suitable for commercial applications. Electronic metering provides information—such as rate of flow and status and alarm indication—and data not typically available through traditional, mechanical meters and registers. Electronic metering minimizes measurement errors due to sand, suspended particles and pressure fluctuations.

    • Open flow tube design prevents flow obstruction to reduce pressure loss
    • Greater turn-down ratio for extended flow ranges and increased revenue
    • Approved connectivity with Badger Meter ORION® endpoints
      • Easy-to-read, 9-digit LCD display, which presents consumption, rate of flow, unit of measure, alarm conditions and firmware version
      • Pressure alarm and pressure and temperature data reported through ORION Cellular LTE-M/LTE endpoints and BEACON® AMA
    • Field programmable registration and reporting features
    • Meter designed for replaceable electronics
    • Single and dual outputs include high resolution industry standard ASCII encoder protocol, scaled/unscaled and 4-20 mA

The Ultrasonic meter is available with an in-line connector for easy connection and installation to ORION endpoints. It is also available with a flying lead for field splice connection.

Description

Applications: Use the Ultrasonic meter for measuring potable cold water in commercial and industrial services. The meter is also ideal for non-potable, reclaimed irrigation water applications or less than optimum water conditions where small particles exist.

E-Series Ultrasonic meters meet and exceed AWWA C715 and the most recent revision of AWWA C750 Standards. The lead-free bronze alloy meters comply with the lead-free provisions of the Safe Drinking Water Act and NSF/ANSI Standards 61 and 372. E-Series Ultrasonic meters also conform to UL 327B and FM 1044 for fire service applications.

Operation & Performance: As water flows into the measuring tube, ultrasonic signals are sent consecutively in forward and reverse directions of flow. Velocity is then determined by measuring the time difference between the measurement in the forward and reverse directions. Total volume is calculated from the measured flow velocity using water temperature and pipe diameter. The LCD shows total volume, unit of measure, rate of flow, firmware, and alarm conditions (reverse-flow, no usage, empty pipe, exceeding max flow, suspected leak, temperature, end of life, and measurement error). In addition to the other indicators and alarms, meters used with or for Badger Meter ORION® endpoints also display pressure alarms and pressure and temperature data on the LCD.

In the normal temperature range of 45…122° F (7…50° C), the Ultrasonic “new meter“ consumption measurement is accurate to:

    • ±1.5% over the normal flow range
    • ±3.0% from the extended low flow range to the minimum flow value

Construction: The E-Series Ultrasonic meter features lead-free bronze alloy meter housing, ultrasonic transducers, a meter-control circuit board with associated wiring, LCD, and battery. Wetted elements are limited to the pressure vessel and transducers. The electronic components are housed and fully potted within a molded, engineered polymer enclosure, which is attached to the meter housing. The transducers extend through the housing and are sealed by O-rings, enabling turbulence-free water flow through the tube. The open flow tube design prevents obstruction of flow to reduce pressure loss and provide long-term accuracy.

Meter Installation: For long-term performance the meter is weatherproof, UV-resistant, fully submersible, and can be installed using horizontal or vertical piping. The registration electronics and battery are encapsulated to withstand harsh environments and protect the electronics in flooded or submerged pit applications. The meter will not measure flow when an “empty pipe“ condition is experienced. An empty pipe is defined as a condition that occurs when the flow sensors are not fully submerged.

Additional information

Normal Test Flow Limits

2.2…2000 gpm

Minimum Test Flow Limits

1.1 gpm

Safe Maximum Operating Condition (SMOC)

2000 gpm

Typical Pressure Loss

1.5 psi @ 1400 gpm (6×18 in)
1.8 psi @ 1400 gpm (6×24 in)

Operating Performance

In the normal temperature range of 45…122° F (7…50° C), new meter consumption
measurement is accurate to:
• 100% ±1.5% over the normal test flow limits
• 100% ±3.0% for the minimum test flow limits

Storage Temperature

– 40…140° F (– 40…60° C)

Maximum Ambient Storage (Storage for One Hour)

150° F (66° C)

Measured-Fluid Temperature Range

34…140° F (1…60° C)

Humidity

0…100% condensing; meter is capable of operating in fully submerged environments

Maximum Working Pressure of Meter Housing

175 psi (12 bar)

Maximum Operating Pressure of Pressure Sensor

150 psi (10 bar)

Pressure Sensor Accuracy

±2% of full scale pressure, up to 150 psi (10 bar)

Register Display

• Consumption (up to nine digits)
• Rate of flow
• Alarms
• Pressure
• Temperature
• Firmware version
• Unit of measure factory programmed for gallons, cubic feet and cubic meters

Totalization Display Resolution

• Gallons: 0.1
• Cubic feet: 0.01
• Cubic meters: 0.001

Battery

3.6-volt lithium thionyl chloride; battery is fully encapsulated within the register
housing and is not replaceable; 10-year battery life

Meter Housing

Lead-free bronze alloy

Measuring Section

Ultrasonic sensors located in the flow tube

Register Housing & Lid

Engineered polymer

Reviews

There are no reviews yet.

Be the first to review “ES 6″ Bronze – E-Series Lead-Free Bronze Alloy”

Your email address will not be published. Required fields are marked *